Promat® SBR Bonding Latex

Advantages

  • Strongly adhering mechanical keycoat
  • Easy to apply

Promat® SBR Bonding Latex is a single pack, synthetic latex for use as a keycoat for fire protective coatings. It is spray applied after first mixing with PROMASPRAY®-F5.

Promat® SBR Bonding Latex forms part of the PROMASPRAY®-C450 and PROMASPRAY®-F5 passive fire protection system and is designed for application to primed steel or concrete substrates.

After mixing with PROMASPRAY®-F5, Promat® SBR Bonding Latex forms a tough, textured, strongly adhering mechanical keycoat. Once the mixture hasccured, neat PROMASPRAY®-C450 or PROMASPRAY®-F5 can be applied over it.

Applications

Keycoat for fire protective coating. To be used with PROMASPRAY® fireproofing product.

Properties and Performance

< #Back#
Alkalinity

Approximately 10pH

Cure By air drying
Density

1kg/m³ (relative)

Drying Time

10 to 36 hours. Varies with ambient conditions but high humidity, low temperature and low air change will hinder cure significantly.

Number Of Coat One or more as required
Theoretical Coverage
  • 40.54m²/bag
  • 60m2 per 37kg of prepared keycoat
  • Practical coverage dependent on surface texture, substrate porosity, application method and technique
Alkalinity

Approximately 10pH

Cure By air drying
Density

1kg/m³ (relative)

Drying Time

10 to 36 hours. Varies with ambient conditions but high humidity, low temperature and low air change will hinder cure significantly.

Number Of Coat One or more as required
Theoretical Coverage
  • 40.54m²/bag
  • 60m2 per 37kg of prepared keycoat
  • Practical coverage dependent on surface texture, substrate porosity, application method and technique

< #Back#

Packaging

25 litre or 200kg plastic drums.

Shelf Life

Maximum 6 months.

Storage

• Protect from frost, excessive heat (above 45°C) and strong radiant sunlight.

• Keep in tighty closed containers.

Packaging

25 litre or 200kg plastic drums.

Shelf Life

Maximum 6 months.

Storage

• Protect from frost, excessive heat (above 45°C) and strong radiant sunlight.

• Keep in tighty closed containers.

< #Back#
Substrates Preparation

The substrate shall be clean, dry and free from visible moisture (including condensation), dust, loose millscale, loose rust, oil and any other condition preventin good adhesion.

Typical Substrates Preparation

Please contact Promat Technical Department to confirm compatibility of the primer with Promat® SBR Bonding Latex.

Application Limitations

Promat® SBR Bonding Latex may be applied when the substrate and air temperatures are at least 2°C and rising. Maximum substrate and air temperature is 45°C.

Substrate temperature should be at least 2°C above dew point temperature. Application should not take place if the temperature is 4°C and falling.

Application Method

Add 1 volume of water to 1 volume of Promat® SBR Bonding Latex. Add 20kg of PROMASPRAY®-F5 to 17kg of diluted Promat® SBR Bonding Latex and mix for 3 minutes.

Apply with a rotor/stator type spray machine, or for small areas a gravity fed hopper gun, to give 20-50% coverage of substrate.

Application Setting Time

Over coating interval: When touch dry depending on temperature

Substrates Preparation

The substrate shall be clean, dry and free from visible moisture (including condensation), dust, loose millscale, loose rust, oil and any other condition preventin good adhesion.

Typical Substrates Preparation

Please contact Promat Technical Department to confirm compatibility of the primer with Promat® SBR Bonding Latex.

Application Limitations

Promat® SBR Bonding Latex may be applied when the substrate and air temperatures are at least 2°C and rising. Maximum substrate and air temperature is 45°C.

Substrate temperature should be at least 2°C above dew point temperature. Application should not take place if the temperature is 4°C and falling.

Application Method

Add 1 volume of water to 1 volume of Promat® SBR Bonding Latex. Add 20kg of PROMASPRAY®-F5 to 17kg of diluted Promat® SBR Bonding Latex and mix for 3 minutes.

Apply with a rotor/stator type spray machine, or for small areas a gravity fed hopper gun, to give 20-50% coverage of substrate.

Application Setting Time

Over coating interval: When touch dry depending on temperature

< #Back#

Quality Assurance

Promat products are manufactured to stringent quality control systems to assure that our customers receive materials made to the highest standards. Operating to these standards means that all activities, which have a bearing upon quality, are set out in written procedures. Systematic and thorough checks are made on all materials and their usage. Test equipment is subjected to regular checks and is referred back to national standards. The information given in this data sheet is based on actual tests and is believed to be typical of the product. No guarantee of results is implied however, since conditions of use are beyond our control.

Health & Safety

Adequate ventilation must be provided during use. Avoid contact with the skin and eyes by using eye protection, gloves, barrier cream and a face mask. If the product comes into contact with the skin, wash immediately with soap and water. If the eyes are affected, flush with plenty of water and seek medical attention immediately. A safety data sheet is available from Promat upon request. Promat activities are conducted with due regard to all statutory requirements with appropriate safeguards against exposing employees and the public to health and safety risks.

Quality Assurance

Promat products are manufactured to stringent quality control systems to assure that our customers receive materials made to the highest standards. Operating to these standards means that all activities, which have a bearing upon quality, are set out in written procedures. Systematic and thorough checks are made on all materials and their usage. Test equipment is subjected to regular checks and is referred back to national standards. The information given in this data sheet is based on actual tests and is believed to be typical of the product. No guarantee of results is implied however, since conditions of use are beyond our control.

Health & Safety

Adequate ventilation must be provided during use. Avoid contact with the skin and eyes by using eye protection, gloves, barrier cream and a face mask. If the product comes into contact with the skin, wash immediately with soap and water. If the eyes are affected, flush with plenty of water and seek medical attention immediately. A safety data sheet is available from Promat upon request. Promat activities are conducted with due regard to all statutory requirements with appropriate safeguards against exposing employees and the public to health and safety risks.